2023 TITAN 53 ft

2023

2TVTP5333PD000143

Used

U3PD000143

USED 2023 TITAN 53' 3 AXLE TIPPER TRAILER WITH BOLT ON ROOF Customer application Garbage – Compactor – Removable Roof Base model 53-3-TW-TP OT Removable bolt on roof Style Wedge to suit tipper/compactor Panel configuration To suit compactor application with EHD panels Overall length 53 ft Overall width 102” nominal Overall height 13’ 6” at front & rear approx. to top of roof King pin location 36” Upper coupler Flat style aluminum coupler assembly with stainless steel wear plates set @ 50” high Number of Axles Primary Two (2) Axles 5” Round .580 Wall Straight Spindle – PSI Ready Axle track 77” Suspension Reyco 21B FAB w/ Inner wear pads Location of spreads See axle layout Hub/drum assembly 10 Stud Duralite – Hub Pilot / Centrifuse Drum Disc wheel size 14” x 22.5 – 2” offset Rims Aluminum – LVL 1 Tires Brand Michelin Size 445/50R22.5 Tread XOne XMET Ply 20 Quantity 4 Number of Axles Lift One (1) – See Notes #12, 13 Axles 5” Round .580 Wall Straight Spindle – PSI Ready Axle track 77” Suspension Watson TA 25000 Location of spreads See axle layout Hub/drum assembly 10 Stud Duralite – Hub Pilot / Centrifuse Drum Disc wheel size 14 x 22.5 – 2” offset Rims Aluminum – LVL 1 Tires Brand Michelin Size 445/50R22.5 Tread XOne XMET Ply 20 Quantity 2 Axle layout FRONT-Lift-50-Primary-50-Primary-64-REAR Oil seals SKF Lubricants Synthetic Oil – Chevron Delo 75W-90 Brakes ABS 2S/2M Meritor Wabco Slack adj. Meritor Auto Cam Enclos All axles - c/w dust shields Lift kits AL-86 Lift controls Manual Springs 3 Leaf Frame width 48” Rear bumper Steel, Flush, Wide w/ Center Pin Assembly – 36 ½” ground to center of pin Rubber bumpers None Rubber Tipper T Block Bumpers Tow hooks D-rings Tire carrier None Floor 2 ½” thinwall Floor crossmembers None Landing gear Jost Landing Gear Model A401-G3-19-08 Top rail Titan Tapered V1 Top cross tube qty None – provide spigot for future spring bar Top cross tube type None Rear Door Compactor, overslung hinge, outer tri fold van doors, air release, side finger locks – See Notes # 1 & # 3 Rear Door Seal Rubber Front Door None Tarp header None Tarp basket None Tarp hooks None Tarp/Roof No tarp - removable bolt on roof 3 pc – See Note #7& 8 Mud flaps Style Titan black rubber Location Front of Lift and Rear primary – rear flap reinforced w/ 6” flap Paint Body – color Natural aluminum Run – gear Titan black Hub / drum Same as running gear Rims or Disc Aluminum Light package 2-ID markers & midturn per sidewall, 2-4” dia. per side & 3 rect. In rear light bar, 1 per side ID clearance lights at front – See Note #6 Option #1 Use Round plastic 4 ½” on rear, no stainless cover (anti theft ring) Option #2 All lights LED Access Catwalk Frt None Ladder Frt None Ladder Rear None Steps Frt out None Steps Frt in None Steps Rear None Additional specifications: 1) (2) Winders located at the bottom of door. 1 on each side. 2) Landing gear 38’ 4” approx. from center of landing gear to rear of bumper blocks to suit 48’ Tipper deck length. 3) No Sidegrabs. Door opening to suit bottom of compactor chute which is 60 ¾” from ground. Tipper backstop height 42”. Tri Fold door needs to open and close inside building with 2’ clearance on each side of trailer. 4) Compactor sidewall wear plates 5) Air/Elec plate roadside front wall, add suspension dump, tailgate release & air gauge 6) Install alum 3/16” wear plate on rear 20’ of floor 7) HD rear 1/3 of roof, NGHD remainder 8) Add (2) vents per side on sidewall 9) There is no sill, only a lightbar at rear. Eyebrows to be installed 10) Add (18) tarp hooks around door in door opening so customer can tarp it to eliminate spillage when disconnecting from compactor. (4) per side / (5) top & bottom These tarp hooks are not standard, make out of aluminum square stock x 4” long, drill ¼” hole for bungee S hook to hook into 11) Install Meritor Tire Inflation System a. Axles are to be inverted 12) Haldex long stroke brake chambers 13) Add 10”x10” plasma’d viewing window on front wall 14) Install a ¼” liner to outside front bottom panel 15) Install a piece of the 2” c-cap top rail to underside of front wall each side of coupler plate Weight estimate: 20,600 lbs +/- 3% Volume: 144.8 cubic yards

53 ft