Description
2005 TITAN 48' WALKING FLOOR TRAILER
Base Model 48-2-TW-WF
Style Straight
Overall Length 48 ft
Overall Width 102” Nominal
Overall Height 13’ 1 ¼” Approximately
King Pin Location 36”
Upper Couple Ht 40”
Number of Axles
PRIMARY Two (2)
Axles D22-.625 Wall Dana
Axle Track 77”
Suspension Watson Integra 30,000 lb @ 50”
Hub / Drum Assembly Duralite-10 hole
Disc Wheel Size 14 x 22.5
Rims Aluminum
Tires Brand Michelin
Quantity 4
445/50R22.5
Axle Layout FRONT-Primary-50-Primary-29.5-REAR
Oil Seals Chicago Rawhide
Lubricants Oil
Brakes ABS 4S2M Meritor Wabco
Slack Adj. Haldex Auto
Cam Enclos All Axles – c/w Dust Shields
Lift Kits None
Lift Controls None
Frame Width 48”
Rear Bumper Flush Rear bumper with rubber tipper bumpers & D ring style tow hooks
Tire Carrier None
Landing Gear STD. Jost Landing Gear
Top Rail Tapered H.D.
Top Cross Tube 1 piece 1 spring bar in middle of trailer
Floor Crossmembers 12” Centers X bracing required
Keith Walking Floor Kit Running Floor II – 3” Dia Cylinders
Stal Model & Width 2299 (1914 CWS) 3 ½” (Center wear strip) T-Blocks Rear
Slat Wear Strips None
Continuous Bearing Continuous bearing full length
Side Wall Wear Plates None
Tarp Style None
Tarp Header Front & Rear
Tarp Basket None
Tarp Hooks Install tarp hooks on crossmembers near the sidewall at 48” o/c, 4 hooks on rear door
Axle Fender None
Hyd Fitting
Pressure Wing Coupler
Return Wing Coupler
Mud Flaps
Style Titan Black Rubber
Location Rear
Mud Flaps – Landing Gear None
Access
Catwalk- Front None
J-Ladder-Front J- Ladder centered with flip up step below, installed over air & electrical.
Ladder-Rear Located in center of rear door
Steps-Front-Out None
Steps-Front-Ins None
Steps-Rear Located on driver side so door swings open as far as possible
Additional work completed at KTR :
- Prep trailer
- Pressure wash name and loose paint off trailer
- Pull floor to be turned, clean out bearings
- Remove hydraulic, air and electrical lines as needed from kingpin section
- Cut and remove kingpin section, grind clean areas to be rewelded
- Cut and remove bottom front panel, grind clean, fit new panel and weld in place
- Cut and fit kingpin section into trailer, fit bi-metals to kingpin and trailer, weld all in place
- Reattach hydraulic, air, and electrical to kingpin
- Repair crossmembers as needed
- Turn floor, add wear strips, weld up bolt holes
- Reinstall slats, drill holes and bolt downbolt down
- Install new bulkhead fittings and hydraulic hoses with female wingnut couplers on front of trailer
- Repair replace lights as needed
- Replace inner door hinge, repair winder as needed
- Check ABS operation, replace cable and sensor to repair
- Repair water seal track and install new seal, replace broken tailgate hinge
- Repair frame rail and reinforce both sides
- Repair holes on outside of trailer, patch holes inside trailerSpecifications
Year2005
ManufacturerTITAN
VIN2K9WF1L255H035252
ConditionUsed
Stock NumberU55H035252
Length48 ft
Year2005|
ManufacturerTITAN|
VIN2K9WF1L255H035252|
ConditionUsed|
Stock NumberU55H035252|
Length48 ft|
